DAA Mini Mr. Bulletfeeder

DAA Mini Mr. Bulletfeeder
DAA Mini Mr. Bulletfeeder
DAA Mini Mr. Bulletfeeder
DAA Mini Mr. Bulletfeeder
DAA Mini Mr. Bulletfeeder
Foto 1: DAA Mini Mr. BulletfeederFoto 2: DAA Mini Mr. BulletfeederFoto 3: DAA Mini Mr. BulletfeederFoto 4: DAA Mini Mr. BulletfeederFoto 5: DAA Mini Mr. Bulletfeeder
from € 109.00
incl. MwSt. plus Shipping costs
when shipping to United States of America

Overview

Mini Mr.Bulletfeeder by DAA for Caliber 9/38, .45, .40SW and Rifle Caliber .223, .308 und 6,5 x 55 mm

Product description

The Mini Mr.Bulletfeeder by DAA uses a 6-tube magazine system which holds roughly 100 bullets. It feeds into the same brilliantly reliable dropper die assembly as used on the Mr.Bulletfeeder.

Using a Mr.Bulletfeeder while reloading is a real pleasure. It makes the reloading process faster and much easier. If you have never used one, you are missing out on one of the greatest reloading assists out there! A Bulletfeeder also improves safety, by preventing the need to insert your fingers under the tool head to place your bullets on the brass. Everyone should use one!

The problem of course, is cost. Shooting is expensive, and reloading ammo, while usually cheaper than shooting factory, is not as cheap as it once was…
You need to buy a press, other reloading accessories, not to mention ammo components. For many, by the time all that is purchased, they have stretched their budget about as far as it will go. And the Bulletfeeder gets passed on, for lack of funds.

This was our motivation when setting out to develop a less expensive version of the Mr.Bulletfeeder, and it lead to the new Mini Mr.Bulletfeeder.

Each magazine of bullet tubes needs to be filled by hand before reloading, much in the same way you would fill your primer tubes before starting your reloading session. With a little practice, it will take you about 2 minutes to fill the tube assembly. And this can be done in advance while watching TV in the comfort of your living room. Additional tube assemblies can be purchases separately (or as a bundle), thus allowing you to pre-load 300, 400 or more bullets before starting your reloading session.

While reloading, you will see the bullets drop down in the transparent tube, as they feed into the dropper-die assembly. Once a tube is empty, you simply rotate and click the next tube into place and keep reloading. Transition to the next tube takes just a second or two. Once the entire 6-tube magazine is empty, either reload it by hand, or drop your 2nd assembly into place to continue without delay.

The Mini Mr.Bulletfeeder can be used on any progressive reloading machine which uses the same size dies as Dillon, however please note that the powder funnel we supply with the unit is designed to be used only in the Dillon powder drop! If you wish to use the Mini Mr.Bulletfeeder with another press, you may need to get another powder funnel to expand the brass.
Be aware that the bullet feeder does require a station in your tool head, directly after the powder dropper.

We have found it is difficult to use the Mini Mr.Bulletfeeder on a 1050 when a powder check is being used in the following station. This has to do with the angle in which the powder dropper sits, forcing the bullet dropper to rotate further away, over the next station. This is an issue only on a 1050.

Your Mini Mr.Bulletfeeder by DAA includes:
1 x 6-Tube Bullet Magazine Assembly
1 x Dropper Die Assembly
1 x Expanding powder funnel (Dillon compatible) only with 9mm/.38S/.40/.45 3 x Spare Steel Ball-Bearings for Dropper
1 x User Instruction Sheet

Accessories for DAA Mini Mr. Bulletfeeder

DAA Mini Mr. Bulletfeeder 6-tube Magazine Assembly

€ 49.00
(incl. MwSt. plus shipping costs)

DAA Mr. Bulletfeeder Bullet Dropper Thread-Extention

€ 16.50
(incl. MwSt. plus shipping costs)

DAA Powder Funnel for Hornady LnL

€ 35.00
(incl. MwSt. plus shipping costs)

DAA 2-in-1 Seating and Crimping Die

€ 28.50
(incl. MwSt. plus shipping costs)

Customer Reviews

5 Stars
67
4 Stars
8
3 Stars
0
2 Stars
0
1 Star
0

Most Helpful Customer Reviews

Jean-Valery G. from France in March 2022
Variant: Caliber: 9/38
Prima !!!
Stefan M. from Austria in September 2020
Variant: Caliber: 9/38
Geliefert, in 2 Minuten montiert und gefüllt und den Grinser beim Laden nicht mehr aus dem Gesicht bekommen. Funktioniert wirklich tadellos
Franz H. from Austria in August 2020
Variant: Caliber: .40
Funktion perfekt, erhöht den Ausstoß gewaltig!
Bernhard K. from Austria in November 2019
Variant: Caliber: 9/38
Bin positiv überrascht über die Geschosszuführung! Hätte ich schon viel früher kaufen sollen.
Franz H. from Austria in February 2019
Variant: Caliber: 9/38
1A Gerätschaft, funktioniert ohne langes einstellen, mit allen Geschossformen sehr zuverlässig.
Josef B. from Austria in March 2018
Variant: Caliber: 9/38
schade, hätte dieses Produkt schon früher kaufen sollen
einfach eine Freude damit zu arbeiten
Harry V. from Belgium in July 2017
Variant: Caliber: 9/38
very good, thanks
Peter S. from Austria in June 2016
Variant: Caliber: 9/38
Schnelle und einfache Montage. Wird verwendet in einer Hornady LNL AP.
Funktioniert bestens auch mit kurzen (leichten) Geschossen.

Customers who bought this product also bought

Dillon XL650/XL750 Conversion kit

€ 153.90
(incl. MwSt. plus shipping costs)

Dillon Case Feeder Plate

€ 69.00
(incl. MwSt. plus shipping costs)

Dillon 4-pack Primer Pickup Tubes

€ 51.90
(incl. MwSt. plus shipping costs)

Dillon XL750

€ 949.00
(incl. MwSt. plus shipping costs)

Dillon XL750/XL650 Quick Change kit

€ 216.90
(incl. MwSt. plus shipping costs)

DAA 2-in-1 Seating and Crimping Die

€ 28.50
(incl. MwSt. plus shipping costs)

Hornady die set

€ 79.00
(incl. MwSt. plus shipping costs)

Dillon 750/650/550 Machine Strong Mount

€ 139.00
(incl. MwSt. plus shipping costs)

Dillon Spare Pistol Decapping Pins, pack of 10

€ 12.90
(incl. MwSt. plus shipping costs)

Dillon Case Feeder

€ 369.00
(incl. MwSt. plus shipping costs)